1hp 2hp 3hp 4hp 5hp Head Clean Pool Pump Impeller Swimming Pool Pump 1.1hp
| Model |
Voltage |
HZ |
Power(KW) |
Power(HP) |
Hmax(m) |
Qmax(m³/h) |
Port Size(inch/mm) |
| FL-150 |
220V-240V |
50/60 |
1.1 |
1.5 |
18 |
30 |
2.0/63 |
| FL-200 |
220V-240V |
50/60 |
1.5 |
2 |
19 |
35 |
2.0/63 |
| FL-300 |
220V-240V |
50/60 |
2.2 |
3 |
20 |
38 |
2.0/63 |
| FL-350 |
220V-240V |
50/60 |
2.6 |
3.5 |
21 |
40 |
2.0/63 |
| FL-400 |
380V |
50/60 |
3 |
4 |
22 |
48 |
2.0/63 |
Features:
INSTALLATION
Only qualified licensed electrician should install pump and wiring.
IMPORTANT ELECTRICAL
Electrical Contractors Please Note: All 220/380 Volt 50Hz pumps must be wired to the main power
supply through an approved and correctly rated electrician.
PUMP MOUNT MUST
Be solid Level Rigid Vibration Free.
Allow use of short, direct suction pipe. (To reduce friction losses & don’t install the pump more
than 3M geometrical height from water level)
Allow for gate valves in suction and discharge piping.
Have adequate floor drainage to prevent flooding.
Be protected from excess moisture.
All adequate access for servicing pump and piping.
NOTICE
Pump suction and discharge connections have moulded in thread stops, DO NOT try to screw pipe
in beyond these stops.
OPERATION
NEVER run pump dry! Running pump dry may damage seals, causing leakage and flooding! Fill
pump with water before starting motor.
Before removing lid:
STOP PUMP before proceeding.
CLOSE GATE VALVES in suction and discharge pipes.
RELEASE ALL PRESSURE from pump and piping system.
NEVER tighten or loosen screw while pump is operation.
Description:
WHY OUR PRODUCT: We search for the best products, products that we use and recommend that make your leisure time fun. The LX Whirlpool range of Spa Pumps are standard equipment on Spa Baths and Spa Pools for many of the world’s largest spa manufacturers. The TDA series of pumps have a long reputation for reliability and performance and are specifically engineered for use in a demanding spa environment.
STANDARD OFF CENTRE DISCHARGE: Pumps used on many spas from various spa manufacturers from 2000 onwards. Suitable for all types of spas including Salt, Chlorine, Bromine and Ozone Chlorination. Corrosion Resistant and Chemical-resistant thermoplastic body. Suitable for above ground and in ground spas. If used on a in ground spa and the pump is above the water level then select one of our self-priming pumps from our other listings. If center discharge is required then check our other listings.
WITH A FULL RANGE OF SIZES, they are IDEAL FOR SMALL, MEDIUM and LARGE spas – Our pumps start from the 0.5 HP for circulation pumps up to the 3HP for spa jets and a full range of sizes in between. Connection fittings for standard PVC 2inch (48.5mm) pipe.
HOW TO USE – It is best to always replace your pump with a pump of similar size and power rating. Changing over and fitting of the pump can be done by the handy person but it is recommended to get it done by a professional. Suitable as a direct replacement OR upgrade to existing pump.
This pump is ideal for pool pumping, cleaning, hot water circulation etc. Sometimes people use it for increasing the water pressure in the pipe, garden sprinkling, and irrigation. It only needs solar off grid power to get work! Delivery head of 14 meters and suction up to 8 meters. This pump is simple to install and easy to use. No need of sophisticated knowledge of pumping but just a little imagination of how much you can do with it. It will pump up the water in no time.
